Anritsu 68147C

Call Us: (949)-679-5561

Specials

For example: Agilent E4440A or Anritsu 68369

Signal Generators

Get Quote Add to Quote List

Do you have a 68147C you want to sell?
We buy used equipment!
Learn about selling
Only need this item for a short time? Learn about renting

Model:68147C

Manufactured by: Anritsu

Category:Signal Gen/Synthesizers/Sweepers

Anritsu 68147C - Signal Gen/Synthesizers/Sweepers

Anritsu 68147C Overview

The Anritsu 68C/69B series are your best choice for A.T.E. applications. They pack the highest performance available in a single 13.3 cm package to minimize rack space. High output power assures adequate signal strength to the device under test even after A.T.E. switching and cabling losses.

Accurately leveled output power to –120 dBm in 0.01 dB steps facilitates receiver sensitivity measurements. Fast 5 ms switching time maximizes system throughput. Internal list mode frees the A.T.E. controller to perform measurement analysis tasks. Optional SCPI programmability and free application drivers, including the IVICOM driver and National Instruments LabView® drivers, save you time and money in code generation and maintenance.

The 68100C series are your ideal component test signal sources. Analyze key communications, electronic warfare and RADAR components at baseband, IF and carrier frequencies to 65 GHz. Analyze extremely high-Q components with the optional 0.1 Hz frequency resolution. Step sweep mode delivers synthesized frequency accuracy, or choose analog sweep for the fastest possible sweep times.

With <–60 dBc specified spurious levels, network analysis and power measurement errors are eliminated. Compression measurements are simple with the 0.01 dB resolution available in power sweep mode.

Sophisticated master/slave capability permits two synthesizers to sweep synchronously for mixer or frequency converter measurements. Up, down, harmonically related, and many other inter-dependent sweeps can be configured with the digitally-controlled master/slave capability.

Broad frequency coverage including 0.1 Hz to 65 GHz in a single coax output
Ultra-low SSB phase noise and spurious
+17 dBm guaranteed leveled power to 20 GHz
0.1 Hz optional frequency resolution
<5 ms switching time for <100 MHz sweep steps
Digital frequency sweep and digital power sweep
Wide dynamic range with accurate output levels
Intuitive, menu-driven front panel

Anritsu 68147C All Available Options

01	Rack Mounting: Rack mount kit containing a set of track slides (90° tilt capability), mounting ears, and front panel handles to let the instrument be mounted in a standard 48 cm equipment rack.
06	Phase Modulation (FM) (683xxC and 693xxB): Provides phase modulation capability. FM input, FM output and FM generator become FM/FM input, FM/FM output and FM/FM generator.
07	Delete AM/FM Generators (683xxC and 693xxB): Deletes the internal AM and FM generators. External AM and FM capability remains unchanged. (Not available in combination with Option 8 or Option 20.)
08	Internal Power Measurement (683xxC and 693xxB): Adds an internal power measurement function that is compatible with Anritsu 560-7, 5400-71 or 6400-71 series detectors. (Not available in combination with Option 7)
09	Rear Panel RF Output: Moves RF output connector to the rear panel.
1	Rack Mounting: Rack mount kit containing a set of track slides (90° tilt capability), mounting ears, and front panel handles to let the instrument be mounted in a standard 48 cm equipment rack.
10	User-defined Modulation Capability (683xxC, and 693xxB): Provides user-defined waveform capability. Requires controller (not included). Includes cable and Windows® based software.
11	0.1 Hz Frequency Resolution: Provides frequency resolution of 0.1 Hz.
14	Anritsu 360B VNA Compatibility: Modifies rack mounting hardware to mate the unit in an Anritsu 360B VNA console.
15A	High Power Output (680xxC, 681xxC, 690xxB and 691xxB): Adds high power RF components to the instrument in the 2-20 GHz frequency range.
15B	High Power Output (683xxC and 693xxB): Adds high-power RF components to the instrument in the 2–20 GHz frequency range.
15B	High Power Output (683xxC and 693xxB): Adds high-power RF components to the instrument in the 220 GHz frequency range.
16	High Stability Time Base: Adds an ovenized, 10 MHz crystal oscillator as a high-stability time base. Derate phase noise specification at 10 Hz offset by 8 dB.
17A	Delete Front Panel (68100C, 68300C, 69100B and 69300B): Deletes the front panel for use in remote control applications where a front panel display and keyboard control are not needed.
17B	Delete Front Panel (68000C and 69000B): Deletes the front panel for use in remote control applications where a front panel display and keyboard control are not needed.
18	mmWave Bias Output: Adds rear panel bias output to drive 54000-xWRxx millimeter wave source modules. BNC Twinax connector. (Not available in combination with Option 20.)
19	SCPI Programmability: Adds GPIB command mnemonics complying with Standard Commands for Programmable Instruments (SCPI), Version 1993.0. SCPI programming complies with IEEE 488.2–1987.
19	SCPI Programmability: Adds GPIB command mnemonics complying with Standard Commands for Programmable Instruments (SCPI), Version 1993.0. SCPI programming complies with IEEE 488.21987.
20	SCAN Modulator: Adds an internal SCAN modulator for simulating high-depth amplitude modulated signals in models 68337C, 68347C, 69337B and 69347B only. Requires an external modulating signal input. (Not available in combination with Option 7, Option 18, or Option 22.)
21A	(690xxB, 691xxB): Low Phase Noise, Non-pulsed Digital Downconverter replaces standard analog downconverter on units with low frequency limit of 10 MHz. CW only from 10 MHz to 2.2 GHz
21B	(693xxB): Low Phase Noise, Pulsed Digital Downconverter replaces standard analog downconverter on units with low frequency limit of 10 MHz. CW with pulse modulation from 10 MHz to 2.2 GHz
22	0.1 Hz to 10 MHz Audio Frequency: Adds CW and step sweep frequency coverage below 10 MHz. No modulation is available below 10 MHz. Derate output power by 1 dB for =20 GHz and 2 dB for >20 GHz (Not available in combination with Option 20.)
2A	Step Attenuator: Adds a 10 dB/step attenuator for models having a high-end frequency of =20 GHz. Rated RF output power is reduced.
2B	Step Attenuator: Adds a 10 dB/step attenuator for models having a high-end frequency of = 40 GHz. Rated RF output power is reduced.
2C	Step Attenuator: Adds a 10 dB/step attenuator for models having a high-end frequency of = 50 GHz. Rated RF output power is reduced.
2D	Step Attenuator: Adds a 10 dB/step attenuator for models having a high-end frequency of = 60 GHz. Rated RF output power is reduced.
2E	Electronic Step Attenuator: Adds a 10 dB/step electronic attenuator for models having a high-end frequency of =8.4 GHz. Rated RF output power is reduced.
2F	Electronic Step Attenuator: Adds a 10 dB/step electronic attenuator for models having a high-end frequency of =20 GHz. Rated RF output power is reduced.
6	Phase Modulation (FM) (683xxC and 693xxB): Provides phase modulation capability. FM input, FM output and FM generator become FM/FM input, FM/FM output and FM/FM generator.
7	Delete AM/FM Generators (683xxC and 693xxB): Deletes the internal AM and FM generators. External AM and FM capability remains unchanged. (Not available in combination with Option 8 or Option 20.)
8	Internal Power Measurement (683xxC and 693xxB): Adds an internal power measurement function that is compatible with Anritsu 560-7, 5400-71 or 6400-71 series detectors. (Not available in combination with Option 7)
9	Rear Panel RF Output: Moves RF output connector to the rear panel.
9K

How can we help you with today?

Email Address *

Company name

Contact

Phone number

Ietm(s) *

Comment